About This Item
These worked great for my needs and would probably fit any mower with the same specs. My ol Troy Bilt model no. 12A1869F011 walk behind rear wheel drive broke a front wheel the other day. I got to looking on for a replacement and found these, which fit the specs, 1/2" bore diameter, 8" diameter wheel, and 2" wide wheel. I figured since the specs were right and it was one of my front wheels, not the drive wheels, that these should fit just fine. I was right. Since it came with two, I went ahead and changed them both out. Took all of 5 minutes, if that, to install them. I even cleaned up as best I could and greased the axle stud they fit onto. The wheels seem very well made and very durable. I'll bet they'll easily last the 15 years or so I've had the originals. I'm very pleased with these, however, I can't review how well they work on the Honda models they are designed for.
These lawn mower wheels are definitely a robust and very strong. They have nice tread on them and fit the axle perfectly. They might be bigger than you think so be sure to check your measurements.
After 4 years, the rubber load bearing wheels on my ceramic grill compressed so much that it was difficult to roll the grill around the deck. The manufacturer discontinued the cart, so I had to guess what to get. These 8" wheels are hard rubber, not the soft rubber that the original ones were, and everything fit perfectly. It was a simple job to lever - up the grill, stick in some two by fours to get the wheels off the ground and remove 1 nut to swap out the wheels. The main concern was the width of the new wheels, which was a tad wider than the original ones but that didn't matter. Photos show the old wheel where the rubber had deteriorated and the new ones installed. 10 minute job.
I have an 8 - year old Honda HRR216 lawn Mover (Self Propelled). The original OEM wheelset has finally worn down and I thought it was time to get them replaced. I mistakenly bought these Versus the correct ones. These are for the HRN model mowers. The depth of the axle bolt hole is not the same. So in order to tighten the bolt properly, the wheel would have been pinned down. This is my fault for not paying close enough attention.However from what I saw, the build quality of these look pretty good. Im sure they would work just fine on a HRN series mower.
Looks exactly like the tires from the manufacturer. Fit perfectly. Easy to install.
Nice quality and seem they will last for a while. The only issue I have which may have been my overlook so I want to bring this to your attention before buying :👉I used these to replace a older Honda Lawnmower that I have. My lawnmower each wheel has bearings on the inside and outside, these wheels only allow for one sided. So when I tighten the wheels on since It only holds bearings on one side it can be a bit hard to push . If you don't tighten all the way so it'll roll easier then they eventually wobble loose and can fall off.❗So make sure your lawnmower requires bearings on one side of the wheel only. Otherwise nice set
Good fit for portable table saw
These front wheels are built very well. They easily roll over anything and don't slip on grass, leaves, nor concrete.
Chido
My Hr215 is a rear wheel drive mower so the rear wheels must be specific for this mower. The front wheels only bolt into the front of the mower and can be more flexible. That said, these don't look exactly like the original wheels but they work just fine. I also bought new axel bolts that I knew would fit these wheels so everything is new, fits together and works smoothly. Not a bad price, especially as I enjoy yard work a bit more now.
Front Wheels: These easily fit to my mower with no issues using the OEM hardware. The one thing I noted was that they didn't quite work as well being quite stiff and seemed to slip a little as the mower moved. Maybe it is a breaking in with time thing. Will have to wait and see.Back Wheels: I was going to do a separate review since I obtained them separately but keeps redirecting me to edit my front wheel review. I had a little bit of issue installing these. With them in place, the hardware didn't really want to line up with the bolt hole and it took several minutes of fiddling around to get the bolt in. After installation they seemed to function well. Smooth rolling and I didn't notice any binding. Traction seems ok.One side note, they have a powerful chemical odor about them. Wear gloves when installing or wash your hands right after because the odor will transfer to your skin.
I've been looking for a replacement tires for my lawnmower and these are exactly what I needed. Although the plastic smell coming out of the box was a bit strong. It eventually went away. Decent price and they work pretty good.